DEFENDER2.NET - View topic - Fuel line connectors broken

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Technical > Fuel line connectors broken

Page 2 of 2

Print this entire topic ·

MalteseRover

Member Since: 02 Jul 2013
Location: Gozo
Posts: 131

Hello
i was told such pipes do not like to be warmed up because of age. I have sourced a used plastic connector from the discovery but it looks quite shorter when compared to the defender one.

I was about to try heat the pipe and press it (with some of the outer rubber layer removed as it would foul against the green clip.

I am concerned now as it has been sitting for a week

17th Mar 2023 11:17pm

MalteseRover

Member Since: 02 Jul 2013
Location: Gozo
Posts: 131

hi, I managed to obtain a non defender connector (from a european engine) it is had 3 barbs and as long as the one that i removed. I managed to press it in the pipe but i kinked the pine in one instance

will see how it goes. so far it is running fine. It an 8mm OD connector not the 7.89mm. i managed to push it in the pump from the hatch above.

19th Mar 2023 8:38am

Firebird

Member Since: 27 Oct 2023
Location: Helsinki
Posts: 10

I'm about to replace the fuel hoses WJP107940 on my Defender 110 (yr2000) TD5... as my high pressure hose has a hole in it!

Luckily, I have an inspection hatch in my floor. My questions are... Is it relatively straightforward to physically replace the hoses? Is it just a case of feeding them through and connecting them up?

I know that I have to go through a fuel pump bleeding cycle by pressing the accelerator 5 times etc afterwards... I'm just wondering how hard they are to replace or anything I should know now that'll make it easier to do. I'm very thankful to have the hatch in the floor at least!

27th Oct 2023 10:25am

jst

Member Since: 14 Jan 2008
Location: Taunton
Posts: 7682

2011 Defender 110 Puma 2.4 USW Stornoway Grey

mwestcrew wrote:

The tool to fit them is about £80 plus VAT but it does loads of sizes od push in connectors. Very handy to have.

With the tool you can put male and female couplers onto damaged lines as a repair too.

have you a link to this tool please? Cheers

James
110 XS Utility
130 Puma Station wagon/camper (in the making)
90 Puma Hardtop

27th Oct 2023 7:18pm

Screbble

Member Since: 26 Apr 2015
Location: Lancashire
Posts: 2024

2004 Defender 90 Td5 XS CSW Zambezi Silver

Penfold_6290 wrote:
Great to hear you're sorted, I have an inspection plate in my workshop that has been bought specifically for when I have a fuel pump issue. I plan to cut a hole in the floor to access the pump in situ rather than go through the pain of dropping the tank again. The inspection plate will then be fitted over the hole to maintain a watertight seal between chassis and body. This is how you access the fuel pump in a Discovery, I can't understand why they didn't do similar in a Defender.

Click image to enlarge

I do like that inspection hatch, and having had the ‘enjoyment’ of replacing the pump by dropping the tank on my 90 I’d be keen to install one.

Does anyone have the dimensions for its installation or is it a case of trial holes and error…

27th Oct 2023 7:43pm

mwestcrew

Member Since: 09 Dec 2019
Location: South Warwickshire
Posts: 216

2011 Defender 130 Puma 2.4 HCPU Baltic Blue

Link for tool

https://www.amazon.co.uk/Laser-6933-Pipe-C...amp;nodl=1 2011 130 Utility Body
2005 110 Van

28th Oct 2023 8:24am

Page 2 of 2

All times are GMT + 1 Hour

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum