DEFENDER2.NET - View topic - Grease nipple for Defender Pedal box

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Puma (Tdci) > Grease nipple for Defender Pedal box

Page 1 of 1

Print this entire topic ·

mifa

Member Since: 16 Dec 2022
Location: Denmark
Posts: 18

2007 Defender 90 Puma 2.4 PU Tonga Green

Grease nipple for Defender Pedal box

Good evening

To get a little less resistance in the clutch I would like to mount a grease nipple on the pedal box. They can be purchased in various online stores, but 20-25 pounds in shipping is just over the top when I don't need a large portion of scrap. Does anyone know the thread size so that it can be purchased at the local tractor dealer?
Michael

14th Oct 2025 6:31pm

custom90

Member Since: 21 Jan 2010
Location: South West, England.
Posts: 21012

They are the same size as those that are on the Puma UJ’s.

Which on a 2 piece fitting this is the smaller one in the picture here:
https://www.ebay.co.uk/itm/376437028538?ms...73b58c6ce4

Unfortunately, I don’t have one at hand to measure for you. ____\We|Will|Win/___
____/🇬🇧🇺🇸\____
_//*⛽️🛢️⚙️🧰*\\_

14th Oct 2025 6:39pm

blackwolf

Member Since: 03 Nov 2009
Location: South West England
Posts: 18015

2007 Defender 110 Puma 2.4 DCPU Stornoway Grey

Have a look at my post one up from the bottom here: https://www.defender2.net/forum/post781671.html

There is some debate whether they are the same as the prop shaft, although on balance it is most likely, in which case they are 1/4" UNF. Also be aware that not all Puma shafts are drilled for a nipple (though most seem to be).

14th Oct 2025 6:42pm

mifa

Member Since: 16 Dec 2022
Location: Denmark
Posts: 18

Thanks!

I got the two original propshafts in store because they were replaced with Gwyn Lewis propshafts.

I will see 1) if the shaft are actually drilled and 2) see if it will fit and measure it if others want to have a go not breaking the bank.

Michael

14th Oct 2025 7:17pm

Ianh

Member Since: 17 Sep 2018
Location: Essex
Posts: 2526

blackwolf wrote:
Have a look at my post one up from the bottom here: https://www.defender2.net/forum/post781671.html

There is some debate whether they are the same as the prop shaft, although on balance it is most likely, in which case they are 1/4" UNF. Also be aware that not all Puma shafts are drilled for a nipple (though most seem to be).

Definitely a 1/4 inch UNF, not an M6 , I tested both and the 1/4 UNF was the correct fit.

14th Oct 2025 10:14pm

mifa

Member Since: 16 Dec 2022
Location: Denmark
Posts: 18

Ian

Great, I tested and its drilled out all right, then it just to passe the tractor supply to geet a nipple.

Michael

15th Oct 2025 5:51am

Ianh

Member Since: 17 Sep 2018
Location: Essex
Posts: 2526

I suspect Yours is left hand drive. This may be an issue as the pivot pin ( if threaded - not all are) is threaded on the right hand side of the pedal box ( as you look at it standing in front of the vehicle) . It’s the same on a left hand drive vehicle which means there is very limited access due to the wing.

See this topic https://www.defender2.net/forum/topic22839-15.html

15th Oct 2025 10:59am

Page 1 of 1

All times are GMT + 1 Hour

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum