DEFENDER2.NET - View topic - Land Rover 110 V8 cast manifolds to Range Rover conversion

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > V8 > Land Rover 110 V8 cast manifolds to Range Rover conversion

Page 1 of 1

Print this entire topic ·

Electron

Member Since: 28 May 2016
Location: Bideford
Posts: 50

Land Rover 110 V8 cast manifolds to Range Rover conversion

Sorry been lurking for a while but now a good way into my 110 V8 (1985) rebuild and improvement. I'd read about moving to Range Rover cast manifolds but never found a post with all the bits photographed. For mine I needed the two cast iron manifolds + two down pipes + Y piece but I also needed to change the gearbox crossmember.

Old Manifolds + Downpipes

Click image to enlarge

New Manifolds + Downpipes

Click image to enlarge

Crossmembers

Click image to enlarge

25th May 2024 11:35am

Electron

Member Since: 28 May 2016
Location: Bideford
Posts: 50

This is the crossmember in showing the gaps each end for the down pipes ...

Click image to enlarge

25th May 2024 12:13pm

Ranger 6

Member Since: 17 Jan 2019
Location: Yorkshireman trapped in a Surrey postcode
Posts: 211

1988 Defender 90 V8 Petrol CSW Rimini Red

This is a good mod - I connected mine to a TD5 system, much bigger bore and a sensible increase in noise.

Once done it's worth swapping the needles in the carbs for BBW, that gives a huge improvement in drivability.

https://www.defender2.net/forum/topic72326.html 90 V8 CSW - 1988

4th Jun 2024 9:56am

Electron

Member Since: 28 May 2016
Location: Bideford
Posts: 50

I'm going for these manifolds, Weber 500 downdraft, MegaJolt with the manifild pressure advance and a temperature sensor choke. I'm also sticking a lambda sensor bung somewhere so we can then do a rolling road final tune once we've run it a bit.

6th Jun 2024 7:24pm

Ranger 6

Member Since: 17 Jan 2019
Location: Yorkshireman trapped in a Surrey postcode
Posts: 211

Have you thought about one of the Holley Sniper or FiTech injection systems? 90 V8 CSW - 1988

11th Jun 2024 9:51am

Electron

Member Since: 28 May 2016
Location: Bideford
Posts: 50

Looked at going the full fuel injection route but had quite a lot of other "stuff" to get done. I have a Thor manifold and injector rails ready and waiting. At least with the MegaJolt I'm half way there ....

14th Jun 2024 4:02pm

Electron

Member Since: 28 May 2016
Location: Bideford
Posts: 50

Fits beautifully

Click image to enlarge

28th Sep 2024 4:12pm

Linds Hanson

Member Since: 16 Jan 2021
Location: Cornwall
Posts: 540

I have a pair of good 3.9/4.2 manifolds with good studs if anyone needs some?

2nd Oct 2024 3:29pm

Electron

Member Since: 28 May 2016
Location: Bideford
Posts: 50

TD5 rear section fits physically but mounts are in the wrong place so I went for new chassis mounts so that I don't have problems with replacing down the line ...

Click image to enlarge

21st Oct 2024 3:32pm

Linds Hanson

Member Since: 16 Jan 2021
Location: Cornwall
Posts: 540

Land Rover do a bolt on mount for there

22nd Oct 2024 2:56pm

Ranger 6

Member Since: 17 Jan 2019
Location: Yorkshireman trapped in a Surrey postcode
Posts: 211

Electron wrote:

Click image to enlarge

You won't be surprised to hear that mine has some impact damage on those lower exhaust pipes....

90 V8 CSW - 1988

23rd Oct 2024 1:46pm

Page 1 of 1

All times are GMT

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum