↓ Advertise on Defender2 ↓

Home > V8 > Land Rover 110 V8 cast manifolds to Range Rover conversion
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
Electron



Member Since: 28 May 2016
Location: Bideford
Posts: 40
 
Land Rover 110 V8 cast manifolds to Range Rover conversion
Sorry been lurking for a while but now a good way into my 110 V8 (1985) rebuild and improvement. I'd read about moving to Range Rover cast manifolds but never found a post with all the bits photographed. For mine I needed the two cast iron manifolds + two down pipes + Y piece but I also needed to change the gearbox crossmember.

Old Manifolds + Downpipes



Click image to enlarge

New Manifolds + Downpipes


Click image to enlarge

Crossmembers



Click image to enlarge



Click image to enlarge
Post #1035681 25th May 2024 12:35pm
View user's profile Send private message View poster's gallery Reply with quote
Electron



Member Since: 28 May 2016
Location: Bideford
Posts: 40
 
This is the crossmember in showing the gaps each end for the down pipes ...


Click image to enlarge
Post #1035685 25th May 2024 1:13pm
View user's profile Send private message View poster's gallery Reply with quote
Ranger 6



Member Since: 17 Jan 2019
Location: Yorkshireman trapped in a Surrey postcode
Posts: 196
United Kingdom 1988 Defender 90 V8 Petrol CSW Rimini Red
This is a good mod - I connected mine to a TD5 system, much bigger bore and a sensible increase in noise.

Once done it's worth swapping the needles in the carbs for BBW, that gives a huge improvement in drivability.

https://www.defender2.net/forum/topic72326.html 90 V8 CSW - 1988
Post #1036452 4th Jun 2024 10:56am
View user's profile Send private message View poster's gallery Reply with quote
Electron



Member Since: 28 May 2016
Location: Bideford
Posts: 40
 
I'm going for these manifolds, Weber 500 downdraft, MegaJolt with the manifild pressure advance and a temperature sensor choke. I'm also sticking a lambda sensor bung somewhere so we can then do a rolling road final tune once we've run it a bit.
Post #1036724 6th Jun 2024 8:24pm
View user's profile Send private message View poster's gallery Reply with quote
Ranger 6



Member Since: 17 Jan 2019
Location: Yorkshireman trapped in a Surrey postcode
Posts: 196
United Kingdom 1988 Defender 90 V8 Petrol CSW Rimini Red
Have you thought about one of the Holley Sniper or FiTech injection systems? 90 V8 CSW - 1988
Post #1037092 11th Jun 2024 10:51am
View user's profile Send private message View poster's gallery Reply with quote
Electron



Member Since: 28 May 2016
Location: Bideford
Posts: 40
 
Looked at going the full fuel injection route but had quite a lot of other "stuff" to get done. I have a Thor manifold and injector rails ready and waiting. At least with the MegaJolt I'm half way there ....
Post #1037470 14th Jun 2024 5:02pm
View user's profile Send private message View poster's gallery Reply with quote
Electron



Member Since: 28 May 2016
Location: Bideford
Posts: 40
 
Fits beautifully


Click image to enlarge


Click image to enlarge
Post #1047110 28th Sep 2024 5:12pm
View user's profile Send private message View poster's gallery Reply with quote
Linds Hanson



Member Since: 16 Jan 2021
Location: Cornwall
Posts: 482
United Kingdom 
I have a pair of good 3.9/4.2 manifolds with good studs if anyone needs some?
Post #1047492 2nd Oct 2024 4:29pm
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT + 1 Hour

Jump to  
<  Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
DEFENDER2.NET RSS Feed - All Forums