DEFENDER2.NET - View topic

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Puma (Tdci) > Terratrip

Page 1 of 1

Print this entire topic ·

Apynala

Member Since: 17 Oct 2009
Location: Morroco
Posts: 88

2009 Defender 110 Puma 2.4 SW Chawton White

Terratrip

Hello,

I'd like to fit a terratrip, does anyone know which wires need to be connect on the DSI.

Thanks.

31st Jul 2011 9:27am

Lorryman100

Member Since: 01 Oct 2010
Location: Here
Posts: 2686

Can I ask why you would want to fit this onto a 4 wheel drive defender? The probe should be fitted onto a non driven wheel which the Puma defender lacks? Here are the Electrical and probe connections.

ELECTRICAL CONNECTIONS
Terratrip 1 Black=Ov White=P– Orange=P+
Note this probe CANNOT be used on some early Terratrips where the voltage between P– and P+ is 8 volt. Use only on units where the voltage is 5 volts.
Terratrip 202/303 White=Pin 2 Orange=Pin 10 Black=Pin 11 (Note on Pin 11 you will also have car battery [–] connection).
IMPORTANT NOTE
The universal probe is not waterproof. Protect with fireproof and waterproof material if exposed to excess water. The probes should not be fitted close to the exhaust system, engine block. Upper temperature limit 125 Celsius.
ELECTRONIC UNIT
The electrical supply to the electronic unit MUST be fused (at no more than 2 amps). Use a line fuse, using a separate 12V feed from the remainder of the car’s electrics – from a permanently available supply, (e.g. NOT ignition switch controlled).

Click image to enlarge

If you send me your email address I will send you the pdf files I have for the one I have fitted (not on the Defender though

)

HTH Brian.

EDIT: This is the Defender Hub and axle, and as you can see there is nowhere to mount the probe onto the hub to give the required clearance.

Click image to enlarge

Number 4 shows the Wheel studs and hub.
Number 10 shows the Brake Disc
Number 1 shows the Axle casing.

31st Jul 2011 9:58am

noworries4x4

Member Since: 24 Dec 2010
Location: Newton Abbot Devon
Posts: 1195

Ive fitted mine on the grab handle and speed pulse is easy small bracket off the back of the handbrake backplate and stick the magnet with Araldite to the drum outer edge, mine works fine.
Wiring as per post above If everything is under control you are not going fast enough.

Every Day 16 MY Discovery 4 Commercial Workshop and Escort Vehicle
Weekends 07MY L322 TDV8 Vogue SE
Series 1 80" 3ltr 6cyl with overdrive
No Worries 4X4

31st Jul 2011 11:20am

Apynala

Member Since: 17 Oct 2009
Location: Morroco
Posts: 88

Terratrip

Hello,

Thanks for your replies, we have the roadbook from Vibraction for Morocco, so we need a Terratrip to follow all the points. We bought one from Offroad Attitude in France which can be connected to the electronic pulses of the Defender. It doesn't have probes to be fitted on the propshaft or handbrake drum. When my father called the dealer but no one can be able to give us any diagram.

I need somme help,

Thanks.

31st Jul 2011 12:01pm

Lorryman100

Member Since: 01 Oct 2010
Location: Here
Posts: 2686

Ahh... you learn something new every day

I didn't know you could get a Dual sensor interface for vehicles with electronic speed sensors as I am still in the analogue phase of rallying

It may be worth dropping an email to one of these companies in the UK as I think they will be able to help you:

http://www.interspares.com/
www.peterlloydrallying.co.uk
www.demon-tweeks.co.uk

31st Jul 2011 1:56pm

Apynala

Member Since: 17 Oct 2009
Location: Morroco
Posts: 88

Lorryman100 wrote:
Ahh... you learn something new every day I didn't know you could get a Dual sensor interface for vehicles with electronic speed sensors as I am still in the analogue phase of rallying It may be worth dropping an email to one of these companies in the UK as I think they will be able to help you:

http://www.interspares.com/
www.peterlloydrallying.co.uk
www.demon-tweeks.co.uk

Thanks for your links.

31st Jul 2011 3:05pm

TJ101

Member Since: 30 May 2007
Location: Taunton Somerset
Posts: 3750

2015 Defender 110 Puma 2.2 XS CSW Montalcino Red

Easy,, Pick up the speed sensor off the gearbox,, better signal then up behind the dash

Needed one for the cruise control i fitted to my 110,,

Better still,, buy a Brantz instead

California F1, 75th 110 "Kermit", 50th Ann V8, 90 V8 Hybrid, 55 Series 1

Main Brian James Trailer Dealer for South West UK

31st Jul 2011 6:28pm

Apynala

Member Since: 17 Oct 2009
Location: Morroco
Posts: 88

Thanks,

Wil check it.

31st Jul 2011 6:53pm

lrmaniac

Member Since: 04 Feb 2010
Location: Lisboa
Posts: 764

2010 Defender 110 Puma 2.4 DCPU Keswick Green

Hello...

Apynala, what was your solution then ? How did you conected you terratrip ? Wich probe/sensor ? Where ?
Any pics ?

Did anyone fitted any in the meantime besides Apynala ? Need advice!

Thanks!

Regards
Joao

'10 Land Rover Defender 110 CC
'08 BMW F800GS
'64 SIIA Forward Control
'69 SIIA 109 ZA CKD
_____________________________________________
You have the right to remain silent. Anything you say will be misquoted, then used against you.

2nd Feb 2012 4:17pm

deep down

Member Since: 02 May 2012
Location: France
Posts: 204

2007 Defender 110 Puma 2.4 DCPU Zambezi Silver

About to fit a Terratrip, does anyone know where I can get a plug and socket so I can make a harness rather than tap in to the signal wire at the gear box?

20th Feb 2013 6:49am

Page 1 of 1

All times are GMT + 1 Hour

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum