Author |
Message |
Defender Diesel Turbo Tdi Engine Kit (STC939D) |
Eppilihp
6th Oct 2023 8:33pm
|
Forum: Technical · Replies: 3 · Views: 577 · Subject: Defender Diesel Turbo Tdi Engine Kit (STC939D) |
I think that with the kit any 90/110 would be exactly the same as the Defender 90/110 that were produced with the 200tdi engine. Engine mounts remained the same until the 300tdi. But I suspect this ... |
Defender Diesel Turbo Tdi Engine Kit (STC939D) |
Eppilihp
6th Oct 2023 2:58pm
|
Forum: Technical · Replies: 3 · Views: 577 · Subject: Defender Diesel Turbo Tdi Engine Kit (STC939D) |
Hi guys
I know that Land Rover offered a "Defender Diesel Turbo Tdi Engine Kit" to replace the 19J with a 200 Tdi and described this in a fitting kit document (STC939D) from 1992.
Now ... |
Anti roll bar kit does not fit (salisbury rear axle) |
Eppilihp
20th Jun 2023 10:50am
|
Forum: Technical · Replies: 11 · Views: 1695 · Subject: Anti roll bar kit does not fit (salisbury rear axle) |
So how did you install your ARB? With the droplinks on the outside? |
Anti roll bar kit does not fit (salisbury rear axle) |
Eppilihp
13th Jun 2023 4:02pm
|
Forum: Technical · Replies: 11 · Views: 1695 · Subject: Anti roll bar kit does not fit (salisbury rear axle) |
All original |
Anti roll bar kit does not fit (salisbury rear axle) |
Eppilihp
12th Jun 2023 5:08pm
|
Forum: Technical · Replies: 11 · Views: 1695 · Subject: Anti roll bar kit does not fit (salisbury rear axle) |
It's weird. I suspect the mounts on the axle sit a tiny bit further apart and/or are a bit wider since the ARB itself is definitely too small.
I measured my ARB, it's 99.3cm (on the inside), could ... |
Anti roll bar kit does not fit (salisbury rear axle) |
Eppilihp
11th Jun 2023 3:07pm
|
Forum: Technical · Replies: 11 · Views: 1695 · Subject: Anti roll bar kit does not fit (salisbury rear axle) |
I trashed my original rear ARB 15 years ago somewhere in Gabun. Now I thought it might be sensible to install a new ARB kit. So I went and bought a standard one online, plus I organised a spacer becau ... |
Anti roll bar installation |
Eppilihp
11th Jun 2023 3:01pm
|
Forum: Td5 · Replies: 49 · Views: 10499 · Subject: Anti roll bar installation |
Looks like the ARB is bent. The bars towards the axle should be parallel to each other.
Not sure it's bent, it's just not wide enough. Are there different sizes? Could someone with a salisbury axle ... |
Anti roll bar installation |
Eppilihp
9th Jun 2023 3:32pm
|
Forum: Td5 · Replies: 49 · Views: 10499 · Subject: Anti roll bar installation |
I hope you don't mind if I jump in with my set of problems...
I trashed my original rear ARB 15 years ago somewhere in Gabun. Now I thought it might be sensible to install a new ARB kit. So I went ... |
Revotec fan control |
Eppilihp
15th Aug 2022 2:08pm
|
Forum: Tdi · Replies: 2 · Views: 906 · Subject: Revotec fan control |
Thanks for your thoughts. I have a slightly different understanding though:
Since the thermostat opens at 88C I would assume the ideal operating temperature of the engine is more or less 88C. Now ... |
Revotec fan control |
Eppilihp
15th Aug 2022 10:35am
|
Forum: Tdi · Replies: 2 · Views: 906 · Subject: Revotec fan control |
Hi guys
I have spent my 200 Tdi a nice Revotec fan kit, so far so good. The question now is, what is the optimal sensor setting to activate the fan? The thermostat opens at 88° and currently the f ... |
200tdi EGT and Boost Pressure |
Eppilihp
15th Aug 2022 10:14am
|
Forum: Tdi · Replies: 15 · Views: 5158 · Subject: 200tdi EGT and Boost Pressure |
Looks good, cheers! |
200tdi EGT and Boost Pressure |
Eppilihp
6th Aug 2022 10:09am
|
Forum: Tdi · Replies: 15 · Views: 5158 · Subject: 200tdi EGT and Boost Pressure |
Would it be possible for you to upload a pic to show where exactly you installed the sensor? |
200tdi EGT and Boost Pressure |
Eppilihp
12th Jul 2022 2:40pm
|
Forum: Tdi · Replies: 15 · Views: 5158 · Subject: 200tdi EGT and Boost Pressure |
Out of curiosity, where do you measure EGT on a 200 Tdi? I plan to install a sender in mine but I am a bit unsure where about.
cheers
Philippe |
MY88 One Ten chassis question |
Eppilihp
21st Aug 2021 6:26pm
|
Forum: Technical · Replies: 9 · Views: 2137 · Subject: MY88 One Ten chassis question |
You mean if I weld the original Tdi mounts then it won't fit because the frame is higher than the old radiator?
Another thing, it looks as if the 200 Tdi radiator is also slightly slanted inwar ... |
MY88 One Ten chassis question |
Eppilihp
21st Aug 2021 8:47am
|
Forum: Technical · Replies: 9 · Views: 2137 · Subject: MY88 One Ten chassis question |
If you have a full width intercooler, forward of the radiator position, why not just continue to use that, and modify the 200Tdi radiator frame to fit your existing mounts and to clear the steering bo ... |
|