DEFENDER2.NET - View topic - LR / Alpine Subs

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > In Car Electronics > LR / Alpine Subs

Page 1 of 1

Print this entire topic ·

90 Dreamer

Member Since: 13 Jul 2019
Location: Oop North
Posts: 2050

2016 Defender 90 Puma 2.2 HT Corris Grey

LR / Alpine Subs

out of interest , if you were to retro-fit an LR Alpine DH12-18808-BA is the loom adaptor / connector or whatever already in-situ?? and guessing if you have the larger cubby it already has holes for the CA support plate??
or just certain factory models, etc??

if missing what is required for a later Puma XS??

did a search but wasn't sure if you needed Martins loom, etc??

27th Jul 2021 4:31pm

Martin
Site Admin

Member Since: 02 Apr 2007
Location: Hook Norton
Posts: 6477

2015 Defender 90 Puma 2.2 XS CSW Montalcino Red

Only real answer is: check your own vehicle.

My October 2014 build (2015MY) 90 XS didn't have it, but some people on here have reported it in place on lower spec models!

Larger cubby does not have holes ready for the plate, no.

If wiring is missing you need my retrofit loom: https://fnltd.co.uk/shop/defender-alpine-s...-p120.html

1988 90 Td5 NAS soft top

2015 D90 XS SW

27th Jul 2021 4:35pm

90 Dreamer

Member Since: 13 Jul 2019
Location: Oop North
Posts: 2050

thanks for that, presumably simply remove the cubby and have a look under the tunnel carpet??

27th Jul 2021 5:02pm

90 Dreamer

Member Since: 13 Jul 2019
Location: Oop North
Posts: 2050

Does the loom simply route down the transmission tunnel under the carpet ??
Just wondering how much I need to strip out to install?

1st Aug 2021 5:27pm

Co1

Member Since: 19 Aug 2018
Location: North Yorkshire
Posts: 3610

You shouldn’t need to remove the cubby if you have the bulkhead delete. Have a look under it from the back and the loom connector will be there facing the rear. From memory it is orange.

1st Aug 2021 5:56pm

90 Dreamer

Member Since: 13 Jul 2019
Location: Oop North
Posts: 2050

No doesn't appear to be anything there, it was more a question of the routing of a new loom??

1st Aug 2021 7:12pm

Martin
Site Admin

Member Since: 02 Apr 2007
Location: Hook Norton
Posts: 6477

My/our new loom has two branches: 1 routes across the tunnel then up to the headunit; another goes down under the seatbox and across to the battery box for power.

The original sub wiring is built into the bulkhead loom and arrives at the sub from the branch which runs underneath the seatbox.

1988 90 Td5 NAS soft top

2015 D90 XS SW

2nd Aug 2021 1:02pm

90 Dreamer

Member Since: 13 Jul 2019
Location: Oop North
Posts: 2050

thanks Martin so probably easiest to strip some of the carpet out to route..........

presumably the power side would handle an extra USB charger added in as need to sort a cubby supply at the same time??

3rd Aug 2021 9:23am

Martin
Site Admin

Member Since: 02 Apr 2007
Location: Hook Norton
Posts: 6477

You should be able to flip up one side (left/UK passenger) of the tunnel carpet.

Yes I could provide a branch for a permanent fed socket

1988 90 Td5 NAS soft top

2015 D90 XS SW

3rd Aug 2021 11:01am

90 Dreamer

Member Since: 13 Jul 2019
Location: Oop North
Posts: 2050

thank you, how is it best to order??

PM or through your site??

3rd Aug 2021 1:16pm

90 Dreamer

Member Since: 13 Jul 2019
Location: Oop North
Posts: 2050

So thanks to Martins loom we now have a fully installed / working LR Sub and have also added some power in the cubby to run a USB port to charge the boys iPod Touch that has been commandeered to provide extra library duties for more moosic......

Click image to enlarge

22nd Aug 2021 7:26pm

Page 1 of 1

All times are GMT + 1 Hour

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum