DEFENDER2.NET - View topic - Bleeding - Sealey hyrdraulic press

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Off Topic > Bleeding - Sealey hyrdraulic press

Page 1 of 1

Print this entire topic ·

excossack

Member Since: 22 Feb 2012
Location: North West
Posts: 5743

1999 Defender 110 Td5 SW Caledonian Blue

Bleeding - Sealey hyrdraulic press

I have a Sealey hyrdraulic press - yk10blg (no pressure gauge model)
This might seem a daft question, but how do you top up/bleed the hydraulic fluid?
The hand operated pump is seperate i.e not bolted to the side of the press like i have seen some pics of.
When I operate it, normally its on a bench or clamped in a vice so it does'nt move around.

I know I have a slight weep which I is why I need to top up/bleed the fluid(ultimatly I need to replace the seals...) 1999 Defender TD5 110

Regards
John M0VAZ
Econet Station 48 no clock

15th Jun 2020 8:01pm

blackwolf

Member Since: 03 Nov 2009
Location: South West England
Posts: 16881

2007 Defender 110 Puma 2.4 DCPU Stornoway Grey

I'm not familiar with that particular model but they're all much the same. There'll be a filler plug at the non-handle end of the pump, probably on the top surface. If it's a quality pump like an Enerpac it will have a dipstick, but with the generic Chinesium pumps there may not be.

To bleed, just make sure that there's plenty of hydraulic oil in the reservoir (if it's low, raise the non-handle end of the pump slightly) and fully extend the ram. When you release the ram, any air in the system (which will have formed a bubble at the top of the ram) will pass back through to the reservoir. Hey presto, system bled and embolism free! Simples.

If you top it up, use a decent hydraulic oil not something like brake fluid which is harmful on most seals. I generally use Castrol Hyspin AWS22, but places like Machine Mart sell sensible sized containers of hydraulic oil (which is actually good for machine tool moving parts too).

15th Jun 2020 8:22pm

excossack

Member Since: 22 Feb 2012
Location: North West
Posts: 5743

Cheers BW. I shall have a look tonight after getting some hydraulic/jack oil. 1999 Defender TD5 110

Regards
John M0VAZ
Econet Station 48 no clock

16th Jun 2020 8:56am

excossack

Member Since: 22 Feb 2012
Location: North West
Posts: 5743

Got some oil today. Noticed for the first time since owning the press there is a hook to hang the pump off.
With the pump hanging up, I removed the top bung to find this had a dipstick setup with two marks to show min/max. It was dry.

Topped up with around 200ml of fluid.
Worked the ram up and down and undoing the filler air escaped.
I took the view that with the ram compressed that was the best time to top up as when extended all the oil would be in the ram.

So far i think its ok. There is a slight weep on the ram but hopefully still able to press what i need to press.
Thanks BW

The press.

Click image to enlarge 1999 Defender TD5 110

Regards
John M0VAZ
Econet Station 48 no clock

16th Jun 2020 6:56pm

blackwolf

Member Since: 03 Nov 2009
Location: South West England
Posts: 16881

If you top up with the ram extended you'll either never get it retracted or you'll get a massive and unwanted discharge from the vent!

16th Jun 2020 7:21pm

excossack

Member Since: 22 Feb 2012
Location: North West
Posts: 5743

and that woulnt be good! 1999 Defender TD5 110

Regards
John M0VAZ
Econet Station 48 no clock

16th Jun 2020 8:01pm

Page 1 of 1

All times are GMT + 1 Hour

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum