| Author |
Message |
 Badly worn drive shaft / flange |
agentmulder
 12th May 2016 2:19am
|
Forum: Technical · Replies: 49 · Views: 35371 · Subject: Badly worn drive shaft / flange |
Reading this as I have the beginnings of red dust and a wee bit of slop/backlash at the rear, when moving it with the wheels up it sounds like the reflected 'clunk' I hear when driving near a wall.
... |
| Fuel priming tool, where is it intended to fit inline? |
agentmulder
12th May 2016 12:38am
|
Forum: Puma (Tdci) · Replies: 28 · Views: 22760 · Subject: Fuel priming tool, where is it intended to fit inline? |
Good job, seems like there are many solutions to this - including: doing nothing 
I did the tasks as you over last weekend: fuel filter and the two breathers, my trick (if you could call it th ... |
| Gear change, First to Second 'nick' |
agentmulder
11th May 2016 9:13am
|
Forum: Puma (Tdci) · Replies: 53 · Views: 25742 · Subject: Gear change, First to Second 'nick' |
| Zero change with new clutch/bearing, new clutch hydraulics or gearbox oil. |
| 'Empire Tuning' remap - looking for testimonials/advice |
agentmulder
11th May 2016 3:42am
|
Forum: Puma (Tdci) · Replies: 2 · Views: 2635 · Subject: 'Empire Tuning' remap - looking for testimonials/advice |
Hello all,
The local LR performance shop in New Zealand uses Empire Tuning:
http://www.empiretuning.co.uk/defender-remap.php
They offer a standard remap that gives a power increase of 122bhp ... |
| Gear change, First to Second 'nick' |
agentmulder
10th May 2016 9:33pm
|
Forum: Puma (Tdci) · Replies: 53 · Views: 25742 · Subject: Gear change, First to Second 'nick' |
Good tips, but I ordered the parts already, very cheap!
I need to print some mounts for some tools in the back, will use PLA (with low density fill) to test them for size/fit. But that stuff sounds ... |
| Clutch pedal dead zone - ok to tighten it up? |
agentmulder
9th May 2016 10:30pm
|
Forum: Puma (Tdci) · Replies: 6 · Views: 2835 · Subject: Clutch pedal dead zone - ok to tighten it up? |
I'll take that as one vote for YES, DO IT 
🍺 |
| Clutch pedal dead zone - ok to tighten it up? |
agentmulder
9th May 2016 10:12pm
|
Forum: Puma (Tdci) · Replies: 6 · Views: 2835 · Subject: Clutch pedal dead zone - ok to tighten it up? |
Hrrrm, no, I don't follow, likely because I haven't been exposed to what you're talking about.
I just swapped out the master rather than open it up and access the seals...
Say I nee ... |
| Puma 2.4L 110 Defender - interior lights stay on in 'Auto' |
agentmulder
9th May 2016 9:42pm
|
Forum: Puma (Tdci) · Replies: 19 · Views: 9424 · Subject: Puma 2.4L 110 Defender - interior lights stay on in 'Auto' |
Interesting, I wonder how many Ah that stray current eats away over long term storage? 
Meanwhile, this interior lights thing is a blast:
They switch on when I unlock the car remotely! ... |
| Clutch pedal dead zone - ok to tighten it up? |
agentmulder
9th May 2016 9:32pm
|
Forum: Puma (Tdci) · Replies: 6 · Views: 2835 · Subject: Clutch pedal dead zone - ok to tighten it up? |
Gidday,
I replaced my master a whiles back and all the instructions said to make sure I marked the level of thread that the pedal arm made with the master actuation rod thingo.
'It's very impor ... |
| fuel breather pipe |
agentmulder
9th May 2016 9:14pm
|
Forum: Puma (Tdci) · Replies: 199 · Views: 319209 · Subject: fuel breather pipe |
Impressive!
How long did you rattle the idea of that solution around in your head? When faced with destructive 'maintenance' I usually let it sit for a day or two before committing 
The ... |
| fuel breather pipe |
agentmulder
9th May 2016 7:56pm
|
Forum: Puma (Tdci) · Replies: 199 · Views: 319209 · Subject: fuel breather pipe |
Mine was a 110, all makes sense now and I could do it in less than half the time, but what a carry on!
I'm finding it hard to imagine a more dirty/annoying job, what makes the 90 harder? At some st ... |
| Puma 2.4L 110 Defender - interior lights stay on in 'Auto' |
agentmulder
9th May 2016 9:04am
|
Forum: Puma (Tdci) · Replies: 19 · Views: 9424 · Subject: Puma 2.4L 110 Defender - interior lights stay on in 'Auto' |
Pulled out about 10m of wire from various uninstalled accessories today (flood lights, reverse camera and something I'm not sure...)
Anyhoo...
FIXED
aaaand, double bonus - the light dip mot ... |
| Remap - can someone explain what it's all about? |
agentmulder
7th May 2016 9:43pm
|
Forum: Puma (Tdci) · Replies: 12 · Views: 6232 · Subject: Remap - can someone explain what it's all about? |
| If you're in/near Auckland I recommend Stag 4x4. They've looked after my Land Rovers for 25 years and are just a great group of knowledgeable enthusiasts. Have done the EGR, ECU upgrades etc, etc on ... |
| fuel breather pipe |
agentmulder
7th May 2016 10:34am
|
Forum: Puma (Tdci) · Replies: 199 · Views: 319209 · Subject: fuel breather pipe |
Wish I had found this thread before my afternoon under the machine...
So yeah, I've got the crack at the top of the fill breather and I cant be sure if it was already broken but in lowering the tan ... |
| Remap - can someone explain what it's all about? |
agentmulder
6th May 2016 2:42am
|
Forum: Puma (Tdci) · Replies: 12 · Views: 6232 · Subject: Remap - can someone explain what it's all about? |
Hello all,
So I'm new my Defender - and actually new to cars, let alone performance tuning.
It's a 2.4L Puma located in New Zealand - it began its life in the UK however (I'm 3rd owner).
Re ... |
| |
